122 lines
3.8 KiB
Plaintext
122 lines
3.8 KiB
Plaintext
// Test code for Adafruit GPS modules using MTK3329/MTK3339 driver
|
|
//
|
|
// This code turns on the LOCUS built-in datalogger. The datalogger
|
|
// turns off when power is lost, so you MUST turn it on every time
|
|
// you want to use it!
|
|
//
|
|
// Tested and works great with the Adafruit Ultimate GPS module
|
|
// using MTK33x9 chipset
|
|
// ------> http://www.adafruit.com/products/746
|
|
// Pick one up today at the Adafruit electronics shop
|
|
// and help support open source hardware & software! -ada
|
|
|
|
#include <Adafruit_GPS.h>
|
|
#if ARDUINO >= 100
|
|
#include <SoftwareSerial.h>
|
|
#else
|
|
// Older Arduino IDE requires NewSoftSerial, download from:
|
|
// http://arduiniana.org/libraries/newsoftserial/
|
|
// #include <NewSoftSerial.h>
|
|
// DO NOT install NewSoftSerial if using Arduino 1.0 or later!
|
|
#endif
|
|
|
|
// Connect the GPS Power pin to 5V
|
|
// Connect the GPS Ground pin to ground
|
|
// If using software serial (sketch example default):
|
|
// Connect the GPS TX (transmit) pin to Digital 3
|
|
// Connect the GPS RX (receive) pin to Digital 2
|
|
// If using hardware serial (e.g. Arduino Mega):
|
|
// Connect the GPS TX (transmit) pin to Arduino RX1, RX2 or RX3
|
|
// Connect the GPS RX (receive) pin to matching TX1, TX2 or TX3
|
|
|
|
// If using software serial, keep these lines enabled
|
|
// (you can change the pin numbers to match your wiring):
|
|
#if ARDUINO >= 100
|
|
SoftwareSerial mySerial(3, 2);
|
|
#else
|
|
NewSoftSerial mySerial(3, 2);
|
|
#endif
|
|
Adafruit_GPS GPS(&mySerial);
|
|
// If using hardware serial (e.g. Arduino Mega), comment
|
|
// out the above six lines and enable this line instead:
|
|
//Adafruit_GPS GPS(&Serial1);
|
|
|
|
|
|
// Set GPSECHO to 'false' to turn off echoing the GPS data to the Serial console
|
|
// Set to 'true' if you want to debug and listen to the raw GPS sentences
|
|
#define GPSECHO true
|
|
|
|
// this keeps track of whether we're using the interrupt
|
|
// off by default!
|
|
boolean usingInterrupt = false;
|
|
void useInterrupt(boolean); // Func prototype keeps Arduino 0023 happy
|
|
|
|
void setup()
|
|
{
|
|
while (!Serial); // the Leonardo will 'wait' until the USB plug is connected
|
|
|
|
// connect at 115200 so we can read the GPS fast enuf and
|
|
// also spit it out
|
|
Serial.begin(115200);
|
|
Serial.println("Adafruit GPS logging start test!");
|
|
|
|
// 9600 NMEA is the default baud rate for MTK - some use 4800
|
|
GPS.begin(9600);
|
|
|
|
// You can adjust which sentences to have the module emit, below
|
|
// Default is RMC + GGA
|
|
GPS.sendCommand(PMTK_SET_NMEA_OUTPUT_RMCGGA);
|
|
// Default is 1 Hz update rate
|
|
GPS.sendCommand(PMTK_SET_NMEA_UPDATE_1HZ);
|
|
|
|
// the nice thing about this code is you can have a timer0 interrupt go off
|
|
// every 1 millisecond, and read data from the GPS for you. that makes the
|
|
// loop code a heck of a lot easier!
|
|
useInterrupt(true);
|
|
delay(500);
|
|
Serial.print("\nSTARTING LOGGING....");
|
|
if (GPS.LOCUS_StartLogger())
|
|
Serial.println(" STARTED!");
|
|
else
|
|
Serial.println(" no response :(");
|
|
delay(1000);
|
|
}
|
|
|
|
|
|
|
|
void loop() // run over and over again
|
|
{
|
|
// do nothing! all reading and printing is done in the interrupt
|
|
}
|
|
|
|
/******************************************************************/
|
|
|
|
// Interrupt is called once a millisecond, looks for any new GPS data, and stores it
|
|
SIGNAL(TIMER0_COMPA_vect) {
|
|
char c = GPS.read();
|
|
// if you want to debug, this is a good time to do it!
|
|
if (GPSECHO && c) {
|
|
#ifdef UDR0
|
|
UDR0 = c;
|
|
// writing direct to UDR0 is much much faster than Serial.print
|
|
// but only one character can be written at a time.
|
|
#endif
|
|
}
|
|
}
|
|
|
|
void useInterrupt(boolean v) {
|
|
if (v) {
|
|
// Timer0 is already used for millis() - we'll just interrupt somewhere
|
|
// in the middle and call the "Compare A" function above
|
|
OCR0A = 0xAF;
|
|
TIMSK0 |= _BV(OCIE0A);
|
|
usingInterrupt = true;
|
|
} else {
|
|
// do not call the interrupt function COMPA anymore
|
|
TIMSK0 &= ~_BV(OCIE0A);
|
|
usingInterrupt = false;
|
|
}
|
|
}
|
|
|
|
|