116 lines
3.7 KiB
Plaintext
116 lines
3.7 KiB
Plaintext
// Test code for Adafruit GPS modules using MTK3329/MTK3339 driver
|
|
//
|
|
// This code erases the LOCUS built-in datalogger storage
|
|
//
|
|
// Tested and works great with the Adafruit Ultimate GPS module
|
|
// using MTK33x9 chipset
|
|
// ------> http://www.adafruit.com/products/746
|
|
// Pick one up today at the Adafruit electronics shop
|
|
// and help support open source hardware & software! -ada
|
|
|
|
#include <Adafruit_GPS.h>
|
|
#if ARDUINO >= 100
|
|
#include <SoftwareSerial.h>
|
|
#else
|
|
// Older Arduino IDE requires NewSoftSerial, download from:
|
|
// http://arduiniana.org/libraries/newsoftserial/
|
|
// #include <NewSoftwareSerial.h>
|
|
// DO NOT install NewSoftSerial if using Arduino 1.0 or later!
|
|
#endif
|
|
|
|
// Connect the GPS Power pin to 5V
|
|
// Connect the GPS Ground pin to ground
|
|
// If using software serial (sketch example default):
|
|
// Connect the GPS TX (transmit) pin to Digital 3
|
|
// Connect the GPS RX (receive) pin to Digital 2
|
|
// If using hardware serial (e.g. Arduino Mega):
|
|
// Connect the GPS TX (transmit) pin to Arduino RX1, RX2 or RX3
|
|
// Connect the GPS RX (receive) pin to matching TX1, TX2 or TX3
|
|
|
|
// If using software serial, keep these lines enabled
|
|
// (you can change the pin numbers to match your wiring):
|
|
#if ARDUINO >= 100
|
|
SoftwareSerial mySerial(3, 2);
|
|
#else
|
|
NewSoftSerial mySerial(3, 2);
|
|
#endif
|
|
Adafruit_GPS GPS(&mySerial);
|
|
// If using hardware serial (e.g. Arduino Mega), comment
|
|
// out the above six lines and enable this line instead:
|
|
//Adafruit_GPS GPS(&Serial1);
|
|
|
|
|
|
// Set GPSECHO to 'false' to turn off echoing the GPS data to the Serial console
|
|
// Set to 'true' if you want to debug and listen to the raw GPS sentences
|
|
#define GPSECHO false
|
|
|
|
// this keeps track of whether we're using the interrupt
|
|
// off by default!
|
|
boolean usingInterrupt = false;
|
|
void useInterrupt(boolean); // Func prototype keeps Arduino 0023 happy
|
|
|
|
void setup()
|
|
{
|
|
// connect at 115200 so we can read the GPS fast enuf and
|
|
// also spit it out
|
|
Serial.begin(115200);
|
|
Serial.println("Adafruit GPS erase FLASH!");
|
|
|
|
// 9600 NMEA is the default baud rate for MTK
|
|
GPS.begin(9600);
|
|
|
|
GPS.sendCommand(PMTK_SET_NMEA_OUTPUT_OFF);
|
|
|
|
// the nice thing about this code is you can have a timer0 interrupt go off
|
|
// every 1 millisecond, and read data from the GPS for you. that makes the
|
|
// loop code a heck of a lot easier!
|
|
useInterrupt(true);
|
|
|
|
Serial.println("This code will ERASE the data log stored in the FLASH - Permanently!");
|
|
Serial.print("Are you sure you want to do this? [Y/N]: ");
|
|
while (Serial.read() != 'Y') delay(10);
|
|
Serial.println("\nERASING! UNPLUG YOUR ARDUINO WITHIN 5 SECONDS IF YOU DIDNT MEAN TO!");
|
|
delay(5000);
|
|
GPS.sendCommand(PMTK_LOCUS_ERASE_FLASH);
|
|
Serial.println("Erased");
|
|
}
|
|
|
|
|
|
|
|
void loop() // run over and over again
|
|
{
|
|
// If using hardware serial (e.g. Arduino Mega), change this to Serial1, etc.
|
|
if (mySerial.available()) {
|
|
char c = mySerial.read();
|
|
if (c) UDR0 = c;
|
|
}
|
|
}
|
|
|
|
/******************************************************************/
|
|
// Interrupt is called once a millisecond, looks for any new GPS data, and stores it
|
|
SIGNAL(TIMER0_COMPA_vect) {
|
|
char c = GPS.read();
|
|
// if you want to debug, this is a good time to do it!
|
|
if (GPSECHO)
|
|
if (c) UDR0 = c;
|
|
// writing direct to UDR0 is much much faster than Serial.print
|
|
// but only one character can be written at a time.
|
|
|
|
}
|
|
|
|
void useInterrupt(boolean v) {
|
|
if (v) {
|
|
// Timer0 is already used for millis() - we'll just interrupt somewhere
|
|
// in the middle and call the "Compare A" function above
|
|
OCR0A = 0xAF;
|
|
TIMSK0 |= _BV(OCIE0A);
|
|
usingInterrupt = true;
|
|
} else {
|
|
// do not call the interrupt function COMPA anymore
|
|
TIMSK0 &= ~_BV(OCIE0A);
|
|
usingInterrupt = false;
|
|
}
|
|
}
|
|
|
|
|